輕勻質保溫板制作流程

Production process of light uniform quality assurance temperature plate:

1. Raw materials such as cement and fiber are proportioned and pulped by the proportioning system, so that the raw materials are fully mixed and kept uniform.

2. Transport the slurry to the slurry storage tank, keep stirring to keep it uniform, send the slurry to the slurry storage tank and then to the headbox, and mix in the headbox to keep uniformity.

3. The billets fall off from the slurry forming cylinder, and are transported to the irrigation cutting place by the billet receiving machine. The longitudinal cutting edge of the billets is cut by the cutter. The residual materials are transported to the return mixer by the billet receiving machine, and then transported to the slurry storage tank for reuse after being stirred by the mixer.

勻質板防火保溫板是隨著工程對防火等級越來越高，進而研發生產的一種性價比超高的外墻防火保溫材料，一經上市以來其優異的保溫及防火性能就得到了使用客戶的高度認可，市場占有率一度升高。

如果建筑外墻不貼服保溫材料，就會出現室外溫度影響室內溫度冬天造成溫度流失，夏天則會讓室內溫度升高，所以現在外墻保溫成為新建筑必須驗收的工程之一。勻質板防火保溫板人優點就是保溫隔熱，讓室外溫度不受外界影響，間接節能環保，減少碳排放。

同時，勻質板防火保溫板質量輕，易于施工中進行搬運，易裁剪性能也讓工程進度大大提高。

水泥基勻質板做防火隔離帶施工要求是什么呢?水泥基勻質板做防火隔離帶施工的時候其實是有很多要求的，那么朋友們都對它有多少了解呢?如果不清楚的話可以看看今天的文章介紹。

當采用用水泥基勻質板做防火隔離帶時，應滿足以下施工要求：

要求一：防火隔離帶水泥基勻質板應與大面外墻外保溫系統一起自下而上按順序同步施工;不宜在外墻外保溫系統保溫層中先預留位置，再粘貼水泥基勻質板;

要求二：水泥基勻質板應與基層墻面滿粘;

要求三：水泥基勻質板應使用錨栓輔助連接。錨栓間距不應大于300mm，且每塊保溫板上的錨栓數量不應少于1個;

要求四：水泥基勻質板防火隔離帶和外墻外保溫系統應使用相同的抹面膠漿，且抹面膠漿應將保溫材料和錨栓完全覆蓋，防火隔離帶與外墻外保溫系統之間不留縫隙。在隔離帶位置還應加鋪普通耐堿玻纖網布，玻纖網布應先于大面玻纖網布鋪設，上下各超出隔離帶寬度應不小于100mm，左右可對接，對接位置距隔離帶保溫板拼縫位置應不小于100mm。